[1]刘鹏,陆明,史长根,等.爆炸焊接最佳药量窗口及其参数的确定[J].爆破器材,2011,40(03):35-38.
　LIU Peng,LU Ming,SHI Changgen,et al.Research on Optimum Charge Window in Explosive Welding[J].EXPLOSIVE MATERIALS,2011,40(03):35-38.
点击复制

爆炸焊接最佳药量窗口及其参数的确定()
分享到：

《爆破器材》[ISSN:1001-8352/CN:32-1163/TJ]

卷:
40
期数:
2011年03
页码:
35-38
栏目:
安全与测试
出版日期:
2011-06-20

文章信息/Info

Title:
Research on Optimum Charge Window in Explosive Welding
文章编号:
4348
作者:
刘鹏; 陆明; 史长根; 庞敬军
（解放军理工大学工程兵工程学院，江苏南京210007）
Author(s):
LIU Peng;  LU Ming;  SHI Changgen;  PANG Jingjun
Engineering Institute of Engineer Corps, PLA University of Science & Technology (Jiangsu Nanjing, 210007)
关键词:
爆炸焊接; 最佳药量窗口; 可焊性窗口; 装药厚度
Keywords:
explosive welding;  optimum charge window;  weldable window;  charge thickness
分类号:
TG456.6
文献标志码:
A
摘要:
介绍了最佳药量窗口的设想，结合爆速试验结果，推导出了起爆端最小装药厚度计算公式。依据不等厚度布药工艺，给出了爆轰末端装药厚度的计算原则。根据“结合界面不产生过熔”的原则，提出了下临界复板厚度的确定公式，由此完善了最佳药量窗口各参数的计算方法。实践表明最佳药量窗口具有一定的实用价值。
Abstract:
Optimum charge window was introduced in this paper, and combined with the result of explosive velocity experiments, formula of minimum charge thickness at detonation beginning end was deduced. According to the technology of dynamite arrange explosive with unequal thickness, computing principles of charge thickness at detonation terminal end were brought forward. On the basis of the principle that interface can’t be over melted, formula of minimum critical flying plate thickness was proposed. Therefore, the parameters of optimum charge window were completed. Practice shows that optimum charge window is of certain practical values.

参考文献/References:

［1］郑远谋.爆炸焊接和金属复合材料及其工程应用［M］.长沙：中南大学出版社，2002：113~119．［2］王耀华. 金属板材爆炸焊接研究与实践［M］．北京：国防工业出版社，2007：114~123，124~128．［3］陆明，王耀华，尤峻. 爆炸焊接可焊性窗口下限药量试验研究［J］．焊接学报，2002，23（6）：44~46.［4］Yoshikazu H, Kenji M, Yukio K. Detonation Characteristics of Emulsion Explosives as Functions of Void and Volume［C］．Twelfth International Detonation Symposium, 2002：149~157.［5］Yoshida M, Lida M, Tanaka K. Detonation Behavior of Emulsion Explosives Containing Glass Microballoons ［C］．Proceedings of Eighth Symposium(International) on Detonation, 1985： 993~1000.［6］Lee J, Persson P A. Detonation Behavior of Emulsion Explosives［J］．Propellants, Explosives, Pyrotechnics, 1990, 15(5):208~216.［7］Chaudhri M M, Almgren L A, Persson A. Detonation Behavior of WaterinOil Type Emulsion Explosive Containing Glass Microbaloons of Selected Sizes ［C］．Proceedings of the Tenth Symposium on Detonation, 1993： 741~748.［8］宋锦泉. 乳化炸药爆轰特性研究［D］.北京：北京科技大学, 2000.［9］LU M, LIU P, Li L. Research on the motion model of flying plate in explosive welding［J］. Advanced Materials Research, 2010(108~111) :1152~1157．［10］董刚,周春华,史长根,等. 爆炸焊接不等厚度布药工艺［J］．焊接, 2004(6):35~38．［11］周春华, 史长根, 蔡立艮, 等. 爆炸焊接布药工艺的研究［J］．焊接技术，2002，31（6）：17~18.［12］邵炳璜,张凯. 爆炸焊接原理及其工程应用［M］.大连：大连理工大学出版社，1987：296.［13］郑哲敏,杨振声，等. 爆炸加工［M］. 北京：国防工业出版社，1981：402~403.

相似文献/References:

[1]史长根,康丽霞,蒋国良.爆炸焊接两板安全间距分析和试验研究[J].爆破器材,2010,39(03):33.
　SHI Changgen,KANG Lixia,JIANG Guoliang.Analysis and Experimental Study of Safe Space between Two Plates in Explosive Welding[J].EXPLOSIVE MATERIALS,2010,39(03):33.
[2]史长根,冯叔瑜,史和生,等.3Cr13Mo-42CrMo高耐磨耐蚀爆炸焊接复合轧辊试验研究[J].爆破器材,2010,39(05):28.
　SHI Changgen,FENG Shuyu,SHI Hesheng,et al.Trial Study of High Wear-resisting and Acid-resisting Cladding Rolling of 3Cr13Mo-42CrMo in Explosive Welding[J].EXPLOSIVE MATERIALS,2010,39(03):28.
[3]史长根,洪津,蒋国良,等.爆炸焊接危害机理分析[J].爆破器材,2009,38(03):28.
　SHI Changgen,HONG Jin,JIANG Guoliang,et al.Harm Mechanism Analysis of Explosive Welding[J].EXPLOSIVE MATERIALS,2009,38(03):28.
[4]唐文龙①,饶国宁①,周景蓉②,等.SUS304不锈钢/Q345R碳钢爆炸焊接工艺参数研究[J].爆破器材,2012,41(05):29.
　TANG Wenlong,RAO Guoning,ZHOU Jingrong,et al.Study on the Parameters in SUS304 Stainless Steel/Q345R Carbon Steel Explosive Welding Process[J].EXPLOSIVE MATERIALS,2012,41(03):29.
[5]孙光,熊代余,龚兵,等.粉状铵油炸药现场混装车的设计与应用[J].爆破器材,2013,42(05):27.[doi:10.3969/j.issn.1001-8352.2013.05.006]
　SUN Guang,XIONG Daiyu,GONG Bing,et al.Design and Application of Powdery Ammonium Nitrate Fuel Oil Explosive on Site Mixed Loading Truck[J].EXPLOSIVE MATERIALS,2013,42(03):27.[doi:10.3969/j.issn.1001-8352.2013.05.006]
[6]史长根,尤峻.双立式爆炸焊接新方法[J].爆破器材,2008,37(03):28.
　Shi Changgen,You Jun.New Technology of Double Vertical Explosive Welding[J].EXPLOSIVE MATERIALS,2008,37(03):28.
[7]王宇新①,李晓杰①,王小红①,等.基于爆炸焊接技术对磨损失效轧辊的修复研究[J].爆破器材,2018,47(06):8.[doi:10.3969/j.issn.1001-8352.2018.06.002]
　WANG Yuxin,LI Xiaojie,WANG Xiaohong,et al.Study on Repair of Worn Roller Using Explosive Welding Technology[J].EXPLOSIVE MATERIALS,2018,47(03):8.[doi:10.3969/j.issn.1001-8352.2018.06.002]
[8]朱福元①,郭子如②,张仲一②,等.一种平板状爆炸焊接用炸药[J].爆破器材,2021,50(03):40.[doi:10.3969/j.issn.1001-8352.2021.03.008]
　ZHU Fuyuan,GUO Ziru,ZHANG Zhongyi,et al.A Flat Explosive for Explosive Welding[J].EXPLOSIVE MATERIALS,2021,50(03):40.[doi:10.3969/j.issn.1001-8352.2021.03.008]

备注/Memo

备注/Memo:
收稿日期：2010-12-21 作者简介：刘鹏（1979~），男，在读博士生。主要研究方向为金属材料的爆炸加工。
更新日期/Last Update: 2011-06-28