[1]刘晶①②,谢中元①②,王琼林①②,等.三基发射药单螺杆压伸模具流场仿真及实验验证[J].爆破器材,2022,51(01):1-8.[doi:10.3969/j.issn.1001-8352.2022.01.001]
　LIU Jing,XIE Zhongyuan,WANG Qionglin,et al.Simulation and Experimental Verification of Flow Field of Single Screw Extrusion Mold Used in Three-Based Gun Propellant[J].EXPLOSIVE MATERIALS,2022,51(01):1-8.[doi:10.3969/j.issn.1001-8352.2022.01.001]
点击复制

三基发射药单螺杆压伸模具流场仿真及实验验证()
分享到：

《爆破器材》[ISSN:1001-8352/CN:32-1163/TJ]

卷:
51
期数:
2022年01
页码:
1-8
栏目:
基础理论
出版日期:
2022-01-05

文章信息/Info

Title:
Simulation and Experimental Verification of Flow Field of Single Screw Extrusion Mold Used in Three-Based Gun Propellant
文章编号:
5642
作者:
刘晶①②; 谢中元①②; 王琼林①②; 王勇①②; 陈松①②; 许灿啟①②
①西安近代化学研究所(陕西西安,710065)
②氟氮化工资源高效开发与利用国家重点实验室(陕西西安,710065）
Author(s):
LIU Jing①②;  XIE Zhongyuan①②;  WANG Qionglin①②;  WANG Yong①②;  CHEN Song①②;  XU Canqi①②
①Xi’an Modern Chemistry Research Institute (Shaanxi Xi’an, 710065)
②State Key Laboratory of Fluorine & Nitrogen Chemicals (Shaanxi Xi’an, 710065)
关键词:
单螺杆压伸; 流场仿真; 三基发射药; 连续成型
Keywords:
single screw extrusion;  flow field simulation;  three-based gun propellant;  continuous molding
分类号:
TJ55；TQ562
DOI:
10.3969/j.issn.1001-8352.2022.01.001
文献标志码:
A
摘要:
为了实现三基发射药生产工艺中的连续化压伸，同时避免模具内部螺旋状流道造成的三基发射药成型的质量和安全问题，应用ANSYS软件模拟了发射药物料在模具内的挤压过程及模针的受力情况。分析了收缩角、出料方向和模具结构对物料在模具中的温度、模具壁面压力、模针表面受力和物料出料速度分布的影响规律，并通过实验进行了验证。结果表明：模具收缩角越大，模具内压力越大，物料温度也越高，且越容易形成热点，同时模针外表面受到的挤压力和摩擦力也越大，模针越容易出现变形和断裂；竖直挤出过程中，模具壁面压力及模针受力均远大于水平挤出中的相应参数，且容易造成挤出后物料的弯曲；增加多孔板有利于物料在挤出模具中的整流和取向，大幅减少物料的径向流动，降低模针在挤出过程中的受力，且成型质量更好。
Abstract:
In order to realize continuous extrusion in the production process of three-based gun propellant and avoid the quality and safety problems of three-based gun propellant caused by the spiral flow channel inside the mold, extrusion process of propellant in extruder mold and the force of die pin were simulated by ANSYS software.Effects of mold shrinkage angles,extrusion direction and mold structure on temperature of materials in mold,mold wall pressure force on surface of die pin,and velocity distribution of material were analyzed. This change rules were verified by experiment. Result shows that, the larger the mold shrinkage angles, the greater the pressure inside the mold, the higher the material temperature, and the easier it is to form hot spots. At the same time, the greater the extrusion force and friction force on die pin, the more prone the die needle is to deformation and fracture. Mold pressure and force on die pin in the vertical extrusion process are much higher than the corresponding parameters in the horizontal extrusion, and it is easy to cause bending after extrusion in vertical extrusion. Addition of a perforated plate is benefit to rectification and orientation of materials in the extrusion mold, greatly reduced redial flow of materials and force on die pin in extrusion process, and mold quality of propellant is better.

参考文献/References:

［1］常飞,南风强,何卫东. 多孔硝基胍发射药压伸数值仿真及验证［J］. 含能材料,2017,25(2):106-112.
CHANG F, NAN F Q, HE W D. Numerical simulation and verification of porous nitroguanidine gun propellant extrusion［J］. Chinese Journal of Energatic Materials, 2017,25(2):106-112.
［2］韩博.高增面性大弧厚硝基胍发射药工艺技术研究［D］.南京:南京理工大学,2009.
HAN B. Studies on process technology of high progerssice and large arc-thickness NQ-based gun propellant［D］. Nanjing: Nanjing University of Science and Technology, 2009.
［3］张丹丹,何卫东.硝基胍七孔发射药挤压成型过程的数值模拟［J］. 火炸药学报,2015,38(1):82-86.
?ZHANG D D, HE W D. Numerical simulation of 7-hole nitroguanidine-based gun propellant in extrusion forming process［J］. Chinese Journal of Explosices and Propellants, 2015,38(1):82-86.
［4］季丹丹,刘志涛,廖昕,等. 19孔发射药挤出过程的数值模拟与模具优化［J］. 含能材料,2016,24(11):1114-1120.
JI D D, LIU Z T,LIAO X,et al. Numerical simulation of extrusion process and die optimization for 19-hole propellant［J］．Chinese Journal of Energetic MateriaIs,2016,24 (11):1114-1120.
［5］陈富华,胡小秋,刘志涛. 基于有限元分析Workbench软件的多孔发射药挤压过程仿真分析［J］. 兵工学报,2017,38(4):695-703.
CHEN F H,HU X Q,LIU Z T. Workbeneh-based simulation analysis of multi-perforated gun propellant in extrusion process［J］. Acta Armamentarii,2017,38 (4):695-703.
［6］丁亚军，应三九. 螺杆挤出过程中物料在线流变行为及其数值模拟［J］. 兵工学报,2015,36(8):1437-1442.
DING Y J, YING S J. In-line rheological behaviors and numerical simulation of material in extrusion processing［J］. Acta Armamentarii, 2015,36 (8):1437-1442.
［7］ZHOU K, HE Z Q, YIN S P. Numerical simulation for exploring the effect of viscosity on single screw extrusion process of propellant［J］. Procedia Engineering, 2014(84):933-939.
［8］刘林林,马忠亮,高可政,等. 变燃速发射药挤出过程中药料流动计算研究［J］.含能材料,2010,18(5):583-586.
LIU L L,MA Z L,GAO K Z, et al. Computational study of flow for outside layer of variable-burning rate propellant during extrusion［J］. Chinese Journal of Energetic Materials,2010,18(5):583-586.
［9］潘龙,张玉霞,金志明,等. 单螺杆挤出机挤出理论研究进展［J］. 中国塑料, 2009,23(5): 12-19.
PAN L,ZHANG Y X,JIN Z M, et al. Progress in extrusion theory for single-screw extruders［J］. China Plastics, 2009,23(5): 12-19.
［10］于保敏. 塑料成型工艺与模具设计［M］. 北京:清华大学出版社, 2009.
［11］毛玉,王强. 浅析挤出模具口模设计［J］. 工程塑料应用, 2008,36(10): 73-75.
MAO Y, WANG Q. Brief analysis of exetrusion die design［J］. Engineering Plastics Application, 2008,36(10): 73-75.
［12］《火炸药理论与实践》编委会. 火炸药理论与实践［Z］. 北京：中国北方化学工业总公司,2001.
［13］靳国宝,王敏杰,赵丹阳,等. 聚合物双腔微管直角挤出模具非对称流动平衡设计方法［J］. 化工学报,2012,63(11):3478-3485.
JIN G B，WANG M J，ZHAO D Y，et al. A design method of non-symmetry flowing balance for right angle extrusion die of polymeric double-lumen micro-tube［J］. CIESC Journal, 2012,63(11):3478-3485.

备注/Memo

备注/Memo:
收稿日期：2021-08-21
第一作者：刘晶（1988－），女，硕士，工程师，主要从事炸药制造工艺及装备研究。E-mail:15901165735@163.com
通信作者：谢中元（1981－），男，博士，研究员，主要从事火炸药制备工艺的研究。E-mail:5648452522@qq.com
更新日期/Last Update: 2022-01-05